Replies: 7 comments 4 replies
-
|
The screw terminal header. What voltage did you use? |
Beta Was this translation helpful? Give feedback.
-
|
The one marked ac 24 or the other one? I tried a 9v and a 24v sc
…On Sun, May 11, 2025, 07:19 Greg Cormier ***@***.***> wrote:
The screw terminal header. What voltage did you use?
—
Reply to this email directly, view it on GitHub
<#15 (comment)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/AIFHZPURT7GYMFYX3KKQYAL25453ZAVCNFSM6AAAAAB43PMFM6VHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTGMJQGY3TQMY>
.
You are receiving this because you authored the thread.Message ID:
***@***.***
com>
|
Beta Was this translation helpful? Give feedback.
-
|
Any additional thoughts here? Can you show in a photo where the wires hook up to confirm if I did a silly? |
Beta Was this translation helpful? Give feedback.
-
|
Can you share a photo with how you connected power? |
Beta Was this translation helpful? Give feedback.
-
|
Positive on the left side of this connector, negative on the right. |
Beta Was this translation helpful? Give feedback.
-
|
Yes, that will fry your board. That is the connector to use for a temperature sensor. |
Beta Was this translation helpful? Give feedback.
-
|
Where does DC power connect?
…On Tue, May 20, 2025, 15:52 Greg Cormier ***@***.***> wrote:
Yes, that will fry your board. That is the connector to use for a
temperature sensor.
—
Reply to this email directly, view it on GitHub
<#15 (reply in thread)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/AIFHZPSZCGJWXTN7RDMT7W327OIZRAVCNFSM6AAAAAB43PMFM6VHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTGMRRGE3DIMI>
.
You are receiving this because you authored the thread.Message ID:
***@***.***
com>
|
Beta Was this translation helpful? Give feedback.
-
|
You can connect it at the 24VAC terminal. |
Beta Was this translation helpful? Give feedback.
-
|
It may be beneficial to update your documentation to reflect that. I didn't
expect the DC and AC to utilize the same input. Any chance there's a way to
take the pressure sensor itself off and use it with an esp32? Any idea when
you will get stock again so I can order a replacement?
…On Tue, May 20, 2025, 15:55 Greg Cormier ***@***.***> wrote:
You can connect it at the 24VAC terminal.
—
Reply to this email directly, view it on GitHub
<#15 (reply in thread)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/AIFHZPT2PB35AXZZCDXI4O327OJDJAVCNFSM6AAAAAB43PMFM6VHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTGMRRGE3DMMQ>
.
You are receiving this because you authored the thread.Message ID:
***@***.***
com>
|
Beta Was this translation helpful? Give feedback.
-
|
Probably 4-5 weeks until the next batch arrives. Will update the silkscreen and docs. |
Beta Was this translation helpful? Give feedback.
-
|
May want to add which side is positive as well (I assume that matters).
Thanks.
…On Tue, May 20, 2025, 16:44 Greg Cormier ***@***.***> wrote:
Probably 4-5 weeks until the next batch arrives. Will update the
silkscreen and docs.
—
Reply to this email directly, view it on GitHub
<#15 (reply in thread)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/AIFHZPVNEBNB3QTSE6MVHKL27OO5NAVCNFSM6AAAAAB43PMFM6VHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTGMRRGIYTSNY>
.
You are receiving this because you authored the thread.Message ID:
***@***.***
com>
|
Beta Was this translation helpful? Give feedback.
Uh oh!
There was an error while loading. Please reload this page.
-
Where is DC power to be applied? Pretty sure I've fried my board as it no longer works and no longer activates a USB port and it gets super hot where it didn't before (and that's with a known USB power source).
Beta Was this translation helpful? Give feedback.
All reactions