TMC260_Stepper_Motor_Driver_Shield_SKU__DRI0035

thumb|350px|right|TMC260 Stepper Motor Driver Shield SKU:DRI0035 Introduction Do you want to do some projects with stepper motors? A pair of automatic curtains? An XY Plotter? A 3D printer? Generally, it's not been easy to find a powerful stepper motor driver for Arduino, but now this has changed! DFRobot presents the TMC260 Stepper Motor Driver Shield. This shield allows your Arduino to easily drive stepper motors (up to 2A per motor coil, 40V max). Specification Basic Features Key Features Compatible with two-phase stepper motors Compatible with Arduino Up to 2A motor current drive capability Up to 40V DC Simplified communication with standard SPI™ and STEP/DIR interfaces Up to 256 microsteps per full step StallGuard2™: high precision sensorless motor load detection CoolStep™ load dependent current control for energy saving up to 75% microPlyer™ : Microstep interpolator for increased smoothness of microstepping over a STEP/DIR interface SpreadCycle™ High-precision chopper algorithm available as an alternative to the traditional constant off-time algorithm Protection & Diagnostics: overcurrent, short to GND,overtemperature & undervoltage Low Power Dissipation, low RDSON and synchronous rectification Board Overview 700px|left|connect diagram NOTE: We have already lead out some necessary pins on the chip and use mini jumpers to avoid a jumble of cables. } TMC260 Control Mode Selection SPI mode: SDOFF bit is set, the STEP/DIR interface is disabled, and DRVCTRL is the interface for specifying the currents through each coil. STEP/DIR mode:SDOFF bit is clear, the STEP/DIR interface is enabled, and DRVCTRL is a configuration register for the STEP/DIR interface. Tutorial Requirements Hardware Arduino UNO (or similar) x1 TMC260 Stepper Motor Driver Shield x1 Hybrid Stepper Motor for 3D Printer (3.5kg) x1 *Software Arduino IDE V1.0.6 (link) Sample Code Please Download Liberty First: Download Link SPI Sample Code You need to give a “sine” a value in SPI mode using function (tmc26XStepper.SPI_setCoilCurrent(200)) #include <SPI.h> #include <TMC26XStepper.h> //we have a stepper motor with 200 steps per rotation,CS pin 6, dir pin 4, step pin 5 and a current of 800mA TMC26XStepper tmc26XStepper = TMC26XStepper(200,6,4,5,800); void setup() { Serial.begin(9600); Serial.println("=============================="); Serial.println("TMC26X Stepper Driver Demo App"); Serial.println("=============================="); //set this according to you stepper Serial.println("Configuring stepper driver"); //char constant_off_time, char blank_time, char hysteresis_start, char hysteresis_end, char hysteresis_decrement tmc26XStepper.setSpreadCycleChopper(2,24,8,6,0); tmc26XStepper.setRandomOffTime(0); tmc26XStepper.SPI_setCoilCurrent(100); tmc26XStepper.setMicrosteps(128); tmc26XStepper.setStallGuardThreshold(4,0); Serial.println("config finished, starting"); Serial.println("started"); tmc26XStepper.SPI_setSpeed(80); //Set speed at 80 RPM tmc26XStepper.SPI_step(-200); //set step at -200 steps, that is to say stepper will turn a circle reverse tmc26XStepper.spi_start() ; //start stepper delay(2000); //delay 2s tmc26XStepper.SPI_step(200); // set step at 200 steps, stepper will turn a circle forward tmc26XStepper.spi_start() ; delay(2000); tmc26XStepper.SPI_setSpeed(100); // Set speed at 100 RPM tmc26XStepper.SPI_step(-300); // stepper will turn 1.5 circles reverse tmc26XStepper.spi_start() ; delay(2000); tmc26XStepper.SPI_setSpeed(120); // Set speed at 120 RPM tmc26XStepper.SPI_step(400); // stepper will turn 2 circles forward tmc26XStepper.spi_start() ; delay(3000); } void loop() { //you can put stepper control code in loop{} to make stepper works circularly } STEP/DIR Sample Code #include <SPI.h> #include <TMC26XStepper.h> //we have a stepper motor with 200 steps per rotation, CS pin 2, dir pin 6, step pin 7 and a current of 800mA TMC26XStepper tmc26XStepper = TMC26XStepper(200,6,4,5,800); int curr_step; int speed = 0; int speedDirection = 100; int maxSpeed = 1000; void setup() { Serial.begin(9600); Serial.println("=============================="); Serial.println("TMC26X Stepper Driver Demo App"); Serial.println("=============================="); //set this according to you stepper Serial.println("Configuring stepper driver"); //char constant_off_time, char blank_time, char hysteresis_start, char hysteresis_end, char hysteresis_decrement tmc26XStepper.setSpreadCycleChopper(2,24,8,6,0); tmc26XStepper.setRandomOffTime(0); tmc26XStepper.setMicrosteps(128); tmc26XStepper.setStallGuardThreshold(4,0); Serial.println("config finished, starting"); Serial.println("started"); } void loop() { if (!tmc26XStepper.isMoving()) { speed+=speedDirection; if (speed>maxSpeed) { speed = maxSpeed; speedDirection = -speedDirection; } else if (speed<0) { speedDirection = -speedDirection; speed=speedDirection; } //setting the speed Serial.print("setting speed to "); Serial.println(speed); tmc26XStepper.setSpeed(speed); //we want some kind of constant running time - so the length is just a product of speed Serial.print("Going "); Serial.print(10speed); Serial.println(" steps"); tmc26XStepper.step(10speed); } else { //we put out the status every 100 steps if (tmc26XStepper.getStepsLeft()%100==0) { Serial.print("Stall Guard: "); Serial.println(tmc26XStepper.getCurrentStallGuardReading()); } } tmc26XStepper.move(); } Protocol/Library Explantion *TMC26XStepper(int number_of_steps, int cs_pin, int dir_pin, int step_pin, unsigned int current, unsigned int resistor) number_of_steps：Number of steps per rotation cs_pin： CS: enable pin dir_pin：Dir: direction pin step_pin：Step: step pin resistor：sense resistor current scaling default value is 15 ohms(or 150 mohms). It can be ignored when you don't need to use that. *TMC26XSet_SPICS(int cs_pin) cs_pin：CS pin in SPI mode *setConstantOffTimeChopper(char constant_off_time, char blank_time, char fast_decay_time_setting, char sine_wave_offset, unsigned char use_current_comparator) constant_off_time： Off time. This setting controls the duration of the slow decay time and limits the maximum chopper frequency. For most applications an off time within the range of 5μs to 20μs will fit. blank_time：Blanking time.Blanking is the time when the input to the comparator is masked to block these spikes. Set from 0~54。 hysteresis_start： hysteresis start setting that this value is an offset to the hysteresis end value HEND.The range is 1~8 hysteresis_end：hysteresis end setting. Set the hysteresis end value from -3~12 hysteresis_decrement： hysteresis decrementer setting, this setting determines the slope of the hysteresis during on time and during fast decay time *setCurrent(unsigned int current) current： set Current。 *SPI_setCoilCurrent(int Current) Current： Coil Current in SPI mode set from 0 to 248 *setMicrosteps(int number_of_steps) number_of_steps： Microsteps each step set from 0 to 248 *setStallGuardThreshold(char stall_guard_threshold, char stall_guard_filter_enabled) stall_guard_threshold：Set threshold of StallGuard to get logical value of StallGuard stall_guard_filter_enabled： stall guard filter enable（1），stall guard filter disenable（0）。 *step(int steps_to_move) steps_to_move： Set the steps to move and use positive and negative to determine the direction in STEP/DIR mode *setSpeed(unsigned int whatSpeed) whatSpeed： Set RPM (revolutions per minute) in STEP/DIR mode *SPI_step(int spi_steps_to_move) spi_steps_to_move：Set the steps to move and use positive and negative to determine the direction in SPI mode *SPI_setSpeed(unsigned int whatSpeed) whatSpeed：Set RPM (revolutions per minute) in SPI mode *tmc26XStepper.move() Stepper starts to run n STEP/DIR mode *tmc26XStepper.spi_start() Starts to run in SPI mode Troubleshooting ------------ Stepper Motor A stepper motor is a special electromagnetic motor which can convert pulse signals into corresponding angular displacement (or linear displacement). Ordinary motors continuously rotate, but in stepper motors there are two basic states: positioning and revolving. Once there is a pulse input, stepper motor will rotate a certain angle, which we call a "step". Control Mode The TMC260 driver chip has two different control modes: SPI and STEP/DIR interface. The TMC260 requires configuration parameters and mode bits to be set through the SPI before the motor can be driven. The SPI also allows reading back status values and bits. This interface must be used to initialize parameters and modes necessary to enable driving the motor. This interface may also be used for directly setting the currents flowing through the motor coils, as an alternative to stepping the motor using the STEP and DIR signals, so the motor can be controlled through the SPI interface alone. The STEP/DIR interface is a traditional motor control interface available for adapting existing designs to use TRINAMIC motor drivers. Using only the SPI interface requires slightly more CPU overhead to look up the sine tables and send out new current values for the coils. NOTE: Our developers didn’t find the specific formula in the datasheet to calculate this sine. We welcome you to join in development and help us.  **2.STEP/DIR** The STEP/DIR interface is enabled by default. On each active edge, the state sampled from the DIR input determines whether to step forward or back. Each step can be a fullstep or a microstep, in which there are 2, 4, 8, 16, 32, 64, 128, or 256 microsteps per fullstep. During microstepping, a step impulse with a low state on DIR increases the microstep counter and a high decreases the counter by an amount controlled by the microstep resolution. An internal table translates the counter value into the sine and cosine values which control the motor current for microstepping. If you have any questions or cool ideas to share, please visit DFRobot Forum More TMC260 Driver Shield Schematics TMC260 Datasheet TMC260 Driver Libraries shopping online from dfrobot store or dfrobot distributor.