Add RemRam v1 board variant

boards.txt

@@ -493,6 +493,45 @@ Maple.menu.upload_method.serialMethod=Serial
 Maple.menu.upload_method.serialMethod.upload.protocol=maple_serial
 Maple.menu.upload_method.serialMethod.upload.tool=serial_upload
 
+###############################
+# RemRam
+
+RemRam.name=RemRam series
+
+RemRam.build.vid=0x0483
+RemRam.build.pid=0x5711
+RemRam.vid.0=0x0483
+RemRam.pid.0=0x5711
+
+RemRam.build.core=arduino
+RemRam.build.board=RemRam
+RemRam.build.extra_flags=-D{build.product_line} {build.enable_usb} {build.xSerial}
+
+# REMRAM_V1 board
+# Support: Serial1 (USART1 on PA10, PA9)
+RemRam.menu.pnum.REMRAM_V1=RemRam v1
+RemRam.menu.pnum.REMRAM_V1.upload.maximum_size=2097152
+RemRam.menu.pnum.REMRAM_V1.upload.maximum_data_size=524288
+RemRam.menu.pnum.REMRAM_V1.build.mcu=cortex-m7 -mfpu=fpv4-sp-d16 -mfloat-abi=hard
+RemRam.menu.pnum.REMRAM_V1.build.board=REMRAM_V1
+RemRam.menu.pnum.REMRAM_V1.build.series=STM32F7xx
+RemRam.menu.pnum.REMRAM_V1.build.product_line=STM32F765xx
+RemRam.menu.pnum.REMRAM_V1.build.variant=REMRAM_V1
+RemRam.menu.pnum.REMRAM_V1.build.cmsis_lib_gcc=arm_cortexM7l_math
+
+# Virtual COM port
+#RemRam.menu.usb.none=None
+#RemRam.menu.usb.CDC=CDC
+#RemRam.menu.usb.CDC.build.enable_usb={build.usb_flags} -DUSBD_USE_CDC -DUSE_USB_FS
+
+# Upload menu
+RemRam.menu.upload_method.STLinkMethod=STLink
+RemRam.menu.upload_method.STLinkMethod.upload.protocol=STLink
+RemRam.menu.upload_method.STLinkMethod.upload.tool=stlink_upload
+
+RemRam.menu.upload_method.serialMethod=Serial
+RemRam.menu.upload_method.serialMethod.upload.protocol=maple_serial
+RemRam.menu.upload_method.serialMethod.upload.tool=serial_upload
 
 ################################################################################
 # Serialx activation
@@ -532,6 +571,12 @@ Maple.menu.xserial.none.build.xSerial=-DHAL_UART_MODULE_ENABLED -DHWSERIAL_NONE
 Maple.menu.xserial.disabled=Disabled (No Serial)
 Maple.menu.xserial.disabled.build.xSerial=
 
+RemRam.menu.xserial.generic=Enabled with generic Serial
+RemRam.menu.xserial.none=Enabled without generic Serial
+RemRam.menu.xserial.none.build.xSerial=-DHAL_UART_MODULE_ENABLED -DHWSERIAL_NONE
+RemRam.menu.xserial.disabled=Disabled (No Serial)
+RemRam.menu.xserial.disabled.build.xSerial=
+
 # USB connectivity
 Nucleo_144.menu.usb.none=None
 Nucleo_144.menu.usb.HID=HID keyboard and mouse support (if available)
@@ -725,3 +770,29 @@ Maple.menu.opt.o3lto.build.flags.ldspecs=-flto
 Maple.menu.opt.ogstd=Debug (-g)
 Maple.menu.opt.ogstd.build.flags.optimize=-g -Og
 Maple.menu.opt.ogstd.build.flags.ldspecs=
+
+RemRam.menu.opt.osstd=Smallest (-Os default)
+RemRam.menu.opt.oslto=Smallest (-Os) with LTO
+RemRam.menu.opt.oslto.build.flags.optimize=-Os -flto
+RemRam.menu.opt.oslto.build.flags.ldspecs=-flto
+RemRam.menu.opt.o1std=Fast (-O1)
+RemRam.menu.opt.o1std.build.flags.optimize=-O1
+RemRam.menu.opt.o1std.build.flags.ldspecs=
+RemRam.menu.opt.o1lto=Fast (-O1) with LTO
+RemRam.menu.opt.o1lto.build.flags.optimize=-O1 -flto
+RemRam.menu.opt.o1lto.build.flags.ldspecs=-flto
+RemRam.menu.opt.o2std=Faster (-O2)
+RemRam.menu.opt.o2std.build.flags.optimize=-O2
+RemRam.menu.opt.o2std.build.flags.ldspecs=
+RemRam.menu.opt.o2lto=Faster (-O2) with LTO
+RemRam.menu.opt.o2lto.build.flags.optimize=-O2 -flto
+RemRam.menu.opt.o2lto.build.flags.ldspecs=-flto
+RemRam.menu.opt.o3std=Fastest (-O3)
+RemRam.menu.opt.o3std.build.flags.optimize=-O3
+RemRam.menu.opt.o3std.build.flags.ldspecs=
+RemRam.menu.opt.o3lto=Fastest (-O3) with LTO
+RemRam.menu.opt.o3lto.build.flags.optimize=-O3 -flto
+RemRam.menu.opt.o3lto.build.flags.ldspecs=-flto
+RemRam.menu.opt.ogstd=Debug (-g)
+RemRam.menu.opt.ogstd.build.flags.optimize=-g -Og
+RemRam.menu.opt.ogstd.build.flags.ldspecs=

variants/REMRAM_V1/PinNamesVar.h

@@ -0,0 +1,25 @@
+/* SYS_WKUP */
+#ifdef PWR_WAKEUP_PIN1
+    SYS_WKUP1 = PA_0,
+#endif
+#ifdef PWR_WAKEUP_PIN2
+    SYS_WKUP2 = PA_2,
+#endif
+#ifdef PWR_WAKEUP_PIN3
+    SYS_WKUP3 = PC_1,
+#endif
+#ifdef PWR_WAKEUP_PIN4
+    SYS_WKUP4 = PC_13,
+#endif
+#ifdef PWR_WAKEUP_PIN5
+    SYS_WKUP5 = PI_8,
+#endif
+#ifdef PWR_WAKEUP_PIN6
+    SYS_WKUP6 = PI_11,
+#endif
+#ifdef PWR_WAKEUP_PIN7
+    SYS_WKUP7 = NC,
+#endif
+#ifdef PWR_WAKEUP_PIN8
+    SYS_WKUP8 = NC,
+#endif

variants/REMRAM_V1/ldscript.ld

@@ -0,0 +1,167 @@
+/*
+*****************************************************************************
+**
+
+**  File        : LinkerScript.ld
+**
+**  Abstract    : Linker script for STM32F765VITx Device with
+**                2048KByte FLASH, 512KByte RAM
+**
+**                Set heap size, stack size and stack location according
+**                to application requirements.
+**
+**                Set memory bank area and size if external memory is used.
+**
+**  Target      : STMicroelectronics STM32
+**
+**
+**  Distribution: The file is distributed as is, without any warranty
+**                of any kind.
+**
+**  (c)Copyright Ac6.
+**  You may use this file as-is or modify it according to the needs of your
+**  project. Distribution of this file (unmodified or modified) is not
+**  permitted. Ac6 permit registered System Workbench for MCU users the
+**  rights to distribute the assembled, compiled & linked contents of this
+**  file as part of an application binary file, provided that it is built
+**  using the System Workbench for MCU toolchain.
+**
+*****************************************************************************
+*/
+
+/* Entry Point */
+ENTRY(Reset_Handler)
+
+/* Highest address of the user mode stack */
+_estack = 0x20080000;    /* end of RAM */
+/* Generate a link error if heap and stack don't fit into RAM */
+_Min_Heap_Size = 0x200;  /* required amount of heap  */
+_Min_Stack_Size = 0x400; /* required amount of stack */
+
+/* Specify the memory areas */
+MEMORY
+{
+RAM (xrw)      : ORIGIN = 0x20000000, LENGTH = 512K
+FLASH (rx)      : ORIGIN = 0x8000000, LENGTH = 2048K
+}
+
+/* Define output sections */
+SECTIONS
+{
+  /* The startup code goes first into FLASH */
+  .isr_vector :
+  {
+    . = ALIGN(4);
+    KEEP(*(.isr_vector)) /* Startup code */
+    . = ALIGN(4);
+  } >FLASH
+
+  /* The program code and other data goes into FLASH */
+  .text :
+  {
+    . = ALIGN(4);
+    *(.text)           /* .text sections (code) */
+    *(.text*)          /* .text* sections (code) */
+    *(.glue_7)         /* glue arm to thumb code */
+    *(.glue_7t)        /* glue thumb to arm code */
+    *(.eh_frame)
+
+    KEEP (*(.init))
+    KEEP (*(.fini))
+
+    . = ALIGN(4);
+    _etext = .;        /* define a global symbols at end of code */
+  } >FLASH
+
+  /* Constant data goes into FLASH */
+  .rodata :
+  {
+    . = ALIGN(4);
+    *(.rodata)         /* .rodata sections (constants, strings, etc.) */
+    *(.rodata*)        /* .rodata* sections (constants, strings, etc.) */
+    . = ALIGN(4);
+  } >FLASH
+
+  .ARM.extab   : { *(.ARM.extab* .gnu.linkonce.armextab.*) } >FLASH
+  .ARM : {
+    __exidx_start = .;
+    *(.ARM.exidx*)
+    __exidx_end = .;
+  } >FLASH
+
+  .preinit_array     :
+  {
+    PROVIDE_HIDDEN (__preinit_array_start = .);
+    KEEP (*(.preinit_array*))
+    PROVIDE_HIDDEN (__preinit_array_end = .);
+  } >FLASH
+  .init_array :
+  {
+    PROVIDE_HIDDEN (__init_array_start = .);
+    KEEP (*(SORT(.init_array.*)))
+    KEEP (*(.init_array*))
+    PROVIDE_HIDDEN (__init_array_end = .);
+  } >FLASH
+  .fini_array :
+  {
+    PROVIDE_HIDDEN (__fini_array_start = .);
+    KEEP (*(SORT(.fini_array.*)))
+    KEEP (*(.fini_array*))
+    PROVIDE_HIDDEN (__fini_array_end = .);
+  } >FLASH
+
+  /* used by the startup to initialize data */
+  _sidata = LOADADDR(.data);
+
+  /* Initialized data sections goes into RAM, load LMA copy after code */
+  .data : 
+  {
+    . = ALIGN(4);
+    _sdata = .;        /* create a global symbol at data start */
+    *(.data)           /* .data sections */
+    *(.data*)          /* .data* sections */
+
+    . = ALIGN(4);
+    _edata = .;        /* define a global symbol at data end */
+  } >RAM AT> FLASH
+
+
+  /* Uninitialized data section */
+  . = ALIGN(4);
+  .bss :
+  {
+    /* This is used by the startup in order to initialize the .bss secion */
+    _sbss = .;         /* define a global symbol at bss start */
+    __bss_start__ = _sbss;
+    *(.bss)
+    *(.bss*)
+    *(COMMON)
+
+    . = ALIGN(4);
+    _ebss = .;         /* define a global symbol at bss end */
+    __bss_end__ = _ebss;
+  } >RAM
+
+  /* User_heap_stack section, used to check that there is enough RAM left */
+  ._user_heap_stack :
+  {
+    . = ALIGN(8);
+    PROVIDE ( end = . );
+    PROVIDE ( _end = . );
+    . = . + _Min_Heap_Size;
+    . = . + _Min_Stack_Size;
+    . = ALIGN(8);
+  } >RAM
+
+
+
+  /* Remove information from the standard libraries */
+  /DISCARD/ :
+  {
+    libc.a ( * )
+    libm.a ( * )
+    libgcc.a ( * )
+  }
+
+  .ARM.attributes 0 : { *(.ARM.attributes) }
+}